Abstract Back ground: Full coverage porcelain fused to metal crowns (PFM) is commonly recommended for restoration of extensively damaged teeth. Ability of the dentist to adequately prepare teeth is necessary to achieve a proper success and longevity of these restoration. Aims: This study aimed to determine the degree of axial taper and total occlusal convergence angles (TOC) for Porcelain Fused To Metal crowns (PFM) prepared with clinically practiced values, that carried out by dental practitioners in Tripoli center, Libya. Materials and Methods: It was a descriptive, cross-sectional study design and held at Alzendah private dental laboratory, Tripoli Libya. A convenience sample (40) models of Porcelain Fused To Metal Crowns (PFM) preparations carried out by private dental practitioners were scanned by employing a 3D model scanner (Ceramill Map300, Amanngirrbach, Austria). Evaluation of the total occlusal convergence (TOC), bucco-lingual and mesio-distal convergence angles of each abutment tooth was proceeded using B&B dental software (Guide system, B&B, Italy). The degree of taper was measured on the axial walls of each crown preparation and the bucco-lingual and mesio-distal convergence angles subsequently calculated. Results: A total of 40 casts having crown preparations (15 anterior, 25 posterior). The mean convergence angles mesio-distally for all preparations was 40.29° (sd 21.8°), and for the bucco-lingual was 29.92° (sd 9.3°), with mean of TOC was 35.10°. In anterior preparations, the mean bucco-lingual convergence angle was 42.32° (sd 12.2°) compared to 24.52° (sd 15.5°) for posterior preparations (p
Dr. Khaled Omar & Abdussalam Eljabali(1-2022)

Background: Libya has been malaria-free since 1973. The risk of malaria re-introduction to Libya is increasing because of the increase in imported malaria cases due to immigration to Libya from countries where malaria is endemic. Cases are mainly due to P. falciparum and Sub-Saharan Africa is the most common origin. This study was conducted to investigate the prevalence of malaria positive cases among illegal immigrants in the southern region of Libya. Methods: A prospective, observational, multi-center study was conducted. Three hundred and three illegal immigrants from 12 different countries were included. Enzyme-linked immunosorbent assay was used to detect the presence of serum malaria antibodies. Results: A total of 303 immigrants were included in the study with mean age of 25.78±5.92 years. Of them, 195 tested positive for malaria antibodies. Two hundred and sixty nine of the participants came from Brak Al-Shati, 16 from Sebha and 18 from Bergan centers, with 175, 15 and 5 positive cases, respectively. Most of the positive cases (172) arrived in Libya within 1-10 months. The highest number of positive cases (70) came from Ghana followed by (40) from Niger and (39) from Bangladesh. Conclusions: Illegal immigration is a major malaria re-introduction route. The issue of illegal immigration have to be treated urgently to stop the huge influx of illegal immigrants and increase the surveillance activities of infectious diseases in order to keep Libyan territories as a malaria-free lands. Key words: Illegal immigration, Malaria, Libya.
Fadwa Jamaledden Mustafa Kamel Mahanay, Badereddin Bashir K. Annajar, Asma A Ali Oun(11-2021)

one of the main factors that affect the success of the cast crown is the accuracy of the internal and marginal fit, a well-fitting crown reduces the chance for recurrent caries and periodontal disease, whereas the space between a poorly-fitting crown and tooth preparation enables accumulation of bacterial plaque, the use of paint- on die spacing technique to produce the cement gap and subsequently to improve the seating of the cast crowns has become quite popular in the recent years. The purpose of the study is to compare the marginal gap and the internal fit produced by two paint-on die spacing materials (Manicure and paint on die spacer ). Twenty four identical stone dies were made, 12 were coated with paint- on die spacer material, and 12 were coated with nail varnish material, the dies coated with die spacer were divided into three groups (DA,DB,DC), and the dies coated with nail varnish were also divided into three groups (VA,VB,VC), groups DA and VA were coated with one layer, DB and VB were coated with two layers, DC and VC were coated with three layers, for both groups wax patterns were made and casted using the lost waxing technique and all steps were standardized, impression replicas of the casted crowns were made and sectioned by means of the impression replica technique, measurements were taken using Scanning Electron Microscope, from 4 points (marginal gap, mid-axial, axio-occlusal and mid-occlusal). There was no statistical significant difference in accuracy between crowns fabricated on die spacer coated dies and crowns fabricated on nail varnish coated dies. with the crowns fabricated on die spacer coated dies being slightly more accurate.
ABDUSSALAM ELJABALI(12-2019)